Moulds Manufacturing by Micromilling and Electrico-Discharge Machining (Paperback)
5 Angebote vergleichen
Bester Preis: € 36,97 (vom 02.12.2016)1
Moulds Manufacturing by Micromilling and Electrico-Discharge Machining
EN NWISBN: 9783659757266 bzw. 3659757268, in Englisch, LAP Lambert Academic Publishing, neu.
Lieferung aus: Vereinigtes Königreich Großbritannien und Nordirland, zzgl. Versandkosten, in-stock.
In mould manufacturing the most representative component is the cavity, which can represent up to 75% of the total cost of the tooling and can reach 40% of manufacture time. In regions with small sizes and area with difficulty access to the cutting tool with "common'size (>2mm).These areas have been machined by EDM which has a negative impact over the cost and time of manufacture of the mould cavity. Therefore, surveys are developed in order to reduce the use of EDM in industry; among the alternatives, the micromilling process, using high-frequency spindle together with cutting tools smaller than 1 mm of diameter in HSM machine has been emerging as an option for machining small regions in dies and moulds. This book contains the results of the comparison between EDM and micromilling process applied to the mould industry. Machining experiments were carried out on AISI P20 and AISI H13 steels. Residual stress on machined surface, surface finishing, SEM images, microstructure and microhardness and additionally, an analysis of time and cost of manufacturing were carried out. The milling time was approximately 5 times lower than EDM one and generated a savings of 46% in the manufacturing.
In mould manufacturing the most representative component is the cavity, which can represent up to 75% of the total cost of the tooling and can reach 40% of manufacture time. In regions with small sizes and area with difficulty access to the cutting tool with "common'size (>2mm).These areas have been machined by EDM which has a negative impact over the cost and time of manufacture of the mould cavity. Therefore, surveys are developed in order to reduce the use of EDM in industry; among the alternatives, the micromilling process, using high-frequency spindle together with cutting tools smaller than 1 mm of diameter in HSM machine has been emerging as an option for machining small regions in dies and moulds. This book contains the results of the comparison between EDM and micromilling process applied to the mould industry. Machining experiments were carried out on AISI P20 and AISI H13 steels. Residual stress on machined surface, surface finishing, SEM images, microstructure and microhardness and additionally, an analysis of time and cost of manufacturing were carried out. The milling time was approximately 5 times lower than EDM one and generated a savings of 46% in the manufacturing.
2
Moulds Manufacturing by Micromilling and Electrico-Discharge Machining (2015)
EN PB USISBN: 9783659757266 bzw. 3659757268, in Englisch, 112 Seiten, LAP LAMBERT Academic Publishing, Taschenbuch, gebraucht.
से नया: $46.48 (13 प्रदान करता है)
से प्रयोग किया जाता: $64.09 (2 प्रदान करता है)
अधिक दिखाएँ 15 पर प्रदान करता है Amazon.com
Lieferung aus: Vereinigte Staaten von Amerika, Usually ships in 1-2 business days.
Von Händler/Antiquariat, super_star_seller.
In mould manufacturing the most representative component is the cavity, which can represent up to 75% of the total cost of the tooling and can reach 40% of manufacture time. In regions with small sizes and area with difficulty access to the cutting tool with "common"size (>2mm).These areas have been machined by EDM which has a negative impact over the cost and time of manufacture of the mould cavity. Therefore, surveys are developed in order to reduce the use of EDM in industry; among the alternatives, the micromilling process, using high-frequency spindle together with cutting tools smaller than 1 mm of diameter in HSM machine has been emerging as an option for machining small regions in dies and moulds. This book contains the results of the comparison between EDM and micromilling process applied to the mould industry.Machining experiments were carried out on AISI P20 and AISI H13 steels. Residual stress on machined surface, surface finishing, SEM images, microstructure and microhardness and additionally, an analysis of time and cost of manufacturing were carried out. The milling time was approximately 5 times lower than EDM one and generated a savings of 46% in the manufacturing. Paperback, लेबल: LAP LAMBERT Academic Publishing, LAP LAMBERT Academic Publishing, उत्पाद समूह: Book, प्रकाशित: 2015-07-21, रिलीज की तारीख: 2015-07-21, स्टूडियो: LAP LAMBERT Academic Publishing.
Von Händler/Antiquariat, super_star_seller.
In mould manufacturing the most representative component is the cavity, which can represent up to 75% of the total cost of the tooling and can reach 40% of manufacture time. In regions with small sizes and area with difficulty access to the cutting tool with "common"size (>2mm).These areas have been machined by EDM which has a negative impact over the cost and time of manufacture of the mould cavity. Therefore, surveys are developed in order to reduce the use of EDM in industry; among the alternatives, the micromilling process, using high-frequency spindle together with cutting tools smaller than 1 mm of diameter in HSM machine has been emerging as an option for machining small regions in dies and moulds. This book contains the results of the comparison between EDM and micromilling process applied to the mould industry.Machining experiments were carried out on AISI P20 and AISI H13 steels. Residual stress on machined surface, surface finishing, SEM images, microstructure and microhardness and additionally, an analysis of time and cost of manufacturing were carried out. The milling time was approximately 5 times lower than EDM one and generated a savings of 46% in the manufacturing. Paperback, लेबल: LAP LAMBERT Academic Publishing, LAP LAMBERT Academic Publishing, उत्पाद समूह: Book, प्रकाशित: 2015-07-21, रिलीज की तारीख: 2015-07-21, स्टूडियो: LAP LAMBERT Academic Publishing.
3
Moulds Manufacturing by Micromilling and Electrico-Discharge Machining by Bodzia
DE NWISBN: 9783659757266 bzw. 3659757268, in Deutsch, neu.
Lieferung aus: Vereinigtes Königreich Großbritannien und Nordirland, Lieferart: Free, Lieferung: Vereinigtes Königreich Großbritannien und Nordirland, Artikelstandort: GL15SQ Gloucester,United Kingdom, Versandkostenfrei.
Von Händler/Antiquariat, loveourprices2.
Festpreisangebot.
Von Händler/Antiquariat, loveourprices2.
Festpreisangebot.
4
NEW Moulds Manufacturing by Micromilling and Electrico-discharge Machining by Bo
EN NWISBN: 9783659757266 bzw. 3659757268, in Englisch, neu.
Lieferung aus: Vereinigte Staaten von Amerika, Lieferart: Free, Lieferung: Weltweit, Artikelstandort: 45014 Fairfield,OH,USA, Versandkostenfrei.
Von Händler/Antiquariat, grandeagleretail.
Festpreisangebot.
Von Händler/Antiquariat, grandeagleretail.
Festpreisangebot.
5
Moulds Manufacturing by Micromilling and Electrico-Discharge Machining by Bodzia
EN NWISBN: 9783659757266 bzw. 3659757268, in Englisch, neu.
Lieferung aus: Vereinigtes Königreich Großbritannien und Nordirland, Lieferart: Free, Lieferung: Vereinigte Staaten von Amerika, Artikelstandort: GL15SQ United Kingdom, Versandkostenfrei.
Von Händler/Antiquariat, shoppingmadeeasy2.
Festpreisangebot.
Von Händler/Antiquariat, shoppingmadeeasy2.
Festpreisangebot.
Lade…